Frequency-division multiplexing

In frequency-division multiplexing (FDM), the available bandwidth of a communications channel is shared among multiple users by frequency translating, or modulating, each of the individual users onto a different carrier frequency. Assuming sufficient frequency separation of the carrier frequencies that the modulated signals do not overlap, recovery of each of the FDM signals is possible at the receiving end. In order to prevent overlap of the signals and to simplify filtering, each of the modulated signals is separated by a guard band, which consists of an unused portion of the available frequency spectrum. Each user is assigned a given frequency band for all time.

While each user's information signal may be either analog or digital, the combined FDM signal is inherently an analog waveform. Therefore, an FDM signal must be transmitted over an analog channel. Examples of FDM are found in some of the old long-distance telephone transmission systems, including the American N- and L-carrier coaxial cable systems and analog point-to-point microwave systems. In the L-carrier system, illustrated in Figure 4A, a hierarchical combining structure is employed in which 12 voiceband signals are frequency-division multiplexed to form a group signal in the frequency range of 60 to 108 kilohertz. Five group signals are multiplexed to form a supergroup signal in the frequency range of 312 to 552 kilohertz, corresponding to 60 voiceband signals, and 10 supergroup signals are multiplexed to form a master group signal. In the L1 carrier system, deployed in the 1940s, the master group was transmitted directly over coaxial cable. For microwave systems, it was frequency modulated onto a microwave carrier frequency for point-to-point transmission. In the L4 system, developed in the 1960s, six master groups were combined to form a jumbo group signal of 3,600 voiceband signals.

Time-division Multiplexing

Multiplexing also may be conducted through the interleaving of time segments from different signals onto a single transmission path — a process known as time-division multiplexing (TDM). Time-division multiplexing of multiple signals is possible only when the available data rate of the channel exceeds the data rate of the total number of users. While TDM may be applied to either digital or analog signals, in practice it is applied almost always to digital signals. The resulting composite signal is thus also a digital signal.

In a representative TDM system, data from multiple users are presented to a time-division multiplexer. A scanning switch then selects data from each of the users in sequence to form a composite TDM signal consisting of the interleaved data signals. Each user's data path is assumed to be time-aligned or synchronized to each of the other users' data paths and to the scanning mechanism. If only one bit were selected from each of the data sources, then the scanning mechanism would select the value of the arriving bit from each of the multiple data sources. In practice, however, the scanning mechanism usually selects a slot of data consisting of multiple bits of each user's data; the scanner switch is then advanced to the next user to select another slot, and so on. Each user is assigned a given time slot for all time.

Most modern telecommunications systems employ some form of TDM for transmission over long-distance routes. The multiplexed signal may be sent directly over cable systems, or it may be modulated onto a carrier signal for transmission via radio wave. Examples of such systems include the North American T carriers as well as digital point-to-point microwave systems. In T1 systems, introduced in 1962, 24 voiceband signals (or the digital equivalent) are time-division multiplexed together. The voiceband signal is a 64-kilobit-per-second data stream consisting of 8-bit symbols transmitted at a rate of 8,000 symbols per second. The TDM process interleaves 24 8-bit time slots together, along with a single frame-synchronization bit, to form a 193-bit frame. The 193-bit frames are formed at the rate of 8,000 frames per second, resulting in an overall data rate of 1.544 megabits per second. For transmission over more recent T-carrier systems, T1 signals are often further multiplexed to form higher-data-rate signals — again using a hierarchical scheme, as illustrated in Figure 4B.

UNIT 8

Multiple Access

Multiplexing is defined as the sharing of a communications channel through local combining at a common point. In many cases, however, the communications channel must be efficiently shared among many users that are geographically distributed and that sporadically attempt to communicate at random points in time. Three schemes have been devised for efficient sharing of a single channel under these conditions; they are called frequency-division multiple access (FDMA), time-division multiple access (TDMA), and code-division multiple access (CDMA). These techniques can be used alone or together in telephone systems, and they are well illustrated by the most advanced mobile cellular systems.

Frequency-division multiple access

In FDMA the goal is to divide the frequency spectrum into slots and then to separate the signals of different users by placing them in separate frequency slots. The difficulty is that the frequency spectrum is limited and that there are typically many more potential communicators than there are available frequency slots. In order to make efficient use of the communications channel, a system must be devised for managing the available slots. In the advanced mobile phone system (AMPS), the cellular system employed in the United States, different callers use separate frequency slots via FDMA. When one telephone call is completed, a network-managing computer at the cellular base station reassigns the released frequency slot to a new caller. A key goal of the AMPS system is to reuse frequency slots whenever possible in order to accommodate as many callers as possible. Locally within a cell, frequency slots can be reused when corresponding calls are terminated. In addition, frequency slots can be used simultaneously by multiple callers located in separate cells. The cells must be far enough apart geographically that the radio signals from one cell are sufficiently attenuated at the location of the other cell using the same frequency slot.